Lubrication System (for Q.Series and M.Series)
Description
The DYNACUT Lubrication System MDMis a lowlow-pressure system with a coaxial spray nozzle for a fog-free coolant application. The coolant is not atomized but dispensed as fine microdroplets into the air stream at the nozzle tip. With virtually all of the coolant being delivered precisely targeted to the tool and the workpiece, a greater cooling and lubrication is achieved along with the avoidance of cooling mist and a minimalization of coolant waste. This is why, the DYNACUT Lubrication System MDM is optimally suited for milling, drilling, grinding and sawing operations as it increases the tool life, improves the surface quality and enables higher cutting speeds.
In particular, we would like to point out that hazardous substances of any kind, especially substances classified as dangerous according to EC Directive 67/548 / EEC, Article 2, paragraph 2, as well as liquids such as chlorinated hydrocarbons, solutions with alcohol contents of more than 30% gasoline, nitro lacquers and nitro diluents (solvent mixtures for nitro lakes from hydrocarbons and esters) and concentrated acids must not be filled into and distributed with minimal-quantity lubrication systems and components and / or distributed with them.
Features:
- Low-pressure lubrication system
- Precisely targeted spray
- No atomization for protection against cooling mist and reduction of coolant waste
- Operated with an air pressure of 0.3-1.5 bar, depending on the coolant`s viscosity
- Input pressure: max. 8 bar
Scope of Delivery:
- Coolant container 1.5 liter
- Spray head
- Air line
- Liquid line
- Mounting angle with control unit incl. pressure reducer
Technical Specifications of the STEPCRAFT M.500 CNC System
Machine's Footprint (Width, Length, Height) | 23" x 28.6" x 25.4" |
X-Travel | 13.7" (348 mm) |
Y-Travel | 21.4" (543.6 mm) |
Z-Travel | 7.63" (194 mm) |
Gantry Clearance (Z) | 8.07" (205 mm) |
Table Work Area (X, Y) | 20.2" x 25.6" (513 x 650.2 mm) |
Max Feed Rate | 283 in/min (120 mm/sec) |
Lead/Ball Screws | igus dryspin 12x5 mm (optional HIWIN ball screws 12x5 mm) |
Linear Drive | Bosch Rexroth ball bearing linear guides |
Stepper Motors | Sanyo Denki NEMA 23 (1 on X and Z and 2 on Y axes) |
Positional Accuracy/Repeatability | +/- 0.0009" (+/- 0.025 mm) w/igus dryspin +/- 0.0005" (+/- 0.015 mm) w/HIWIN ball screws |
Programmable Resolution | +/- 0.0002" (+/- 0.00625 mm) |
Backlash | +/- 0.0019" (+/- 0.05 mm) w/igus dryspin +/- 0.0012" (+/- 0.03 mm) w/HIWIN ball screws |
Weight | 48.5 lbs (22kg) |
Power Requirements | 110V-240V, 50-60 Hz, 180 watts (Comes with 110V USA plug) |
Interface | USB 2.0 / Parallel (LPT1) / Network RJ-45 |
Computer Requirements | PC with 1Ghz Processor (Laptop, Desktop or All-in-One), USB 2.0 interface, Windows 7 or higher (32/64 bit) OR MAC OS X 10.3.9 or higher with Windows emulation (Parallels or BootCamp) |
Scope Of Delivery
- The M-Series machine will arrive completely ready to run. If you ordered a DIY Kit then it will come with all necessary mechanical and electrical components.
- UCCNC control software
- UC100 Parallel to USB interface
- USB Cable
- Power supply with 110V USA power cable
- 3 x Flexi Guides™
- WERA Tool Set
- Operating Manual
- Detailed assembly manual
Required Tools
- WERA tool set (Included in the DIY Kit)
- 5.5 mm box wrench
- Wire Cutter
- Long-nose pliers
- Cutter Knife
- Digital Calipers
- 3-in-1 oil and grease
System Requirements
- PC with 1GHz processor
- USB Interface (Optional Ethernet)
- Windows XP or higher (32/64 bit)
- MAC OS X 10.3.9 or higher with Windows Emulation